Kimono Dog Harness Pattern + Tutorial
Jill Myslinski uses her time away from her busy restaurant (Acorn Market in Salisbury, Maryland) to sew and create outside of the kitchen. She designed this cute and functional Kimono Dog Harness Tutorial for her dog, and wanted to share it with you and your dog too. You can download your free PDF Kimono Dog Harness Pattern today! Visit Jill’s Acorn Market blog for more, and if you think you can use the pattern give Jill a big THANKS! in the comments…
My Pomeranian/poodle mix Coco loves to go for a walk. Even though she is only 10lbs, she pulls when on a leash. I purchased a small nylon webbing style harness and it helped. But it wasn’t cute. So I took a look at the way it was engineered and duplicated the idea with soft, cuddly fabric. You simply slip your dog’s front paws through the loops and wrap it across his/her back. Velcro will keep it snug. Set aside an hour and make your best friend one soon.
You will need:
- Free PDF Pattern Download
- Tape measure
- 1/3 – 1/2yd. cotton fabric (corduroy and cotton duck are fine as well)
- 1/3 – 1/2yd. polar fleece
- 1 package of bias binding ( or make your own)
- 2 small D-rings (brass or stainless steel)
- 1 package of Velcro (hook and loop tape)
- 1/2yd. 5/8” grosgrain ribbon
1. Measure your dog carefully. Place the tape measure just behind the front paws. Now divide that measurement by 2. Then add 2 ½.” Your final measurement is what you will need to reduce or enlarge the pattern. Take it to the copy center and reduce or enlarge the pattern until the dashed line at the bottom is the same number.
Example: Coco measures 18”. Divide by two = 9. Add 2 1/2” = 11 ½”. I used this number.
2. Layout your fabric. Fold fabric (both print and fleece) with selvages at the top. This will ensure that the grain is perpendicular to the tummy band and will keep it from stretching out as you sew. Cut through the folded fabric once for each fabric giving you two mirror image pieces.
3. With right sides together, sew each piece to its partner. Use a 3/8” seam allowance. Press seams open. Repeat with fleece.
4. With WRONG sides together, pin the cotton fabric to the fleece. There is a small amount of extra fabric at your seam line (for puppy tummies) so you will need to line everything up pretty well. Stay stitch around the entire piece. Stay close to the edge and trim away any sloppy edges.
5. Binding. I use my own, but packaged works well too. There are plenty of good tutorials out there so read up if you are a beginner. Remember, your dog won’t mind if it’s a little sloppy. I like to open the binding and sew it on the top first, using about a 3/8” allowance. Then wrap the folded edge around the back and press, press, press. Carefully stitch in the ditch from the front and you should catch the folded edge around the back.
6. With the fleece side facing you, pull the straps toward you and pin to the closure flaps. There is a mark on the pattern for reference. The strap on the left will go under the flap, the strap on the right will lay on top. Pin and sew across at the binding, hiding the stitches in the ditch. Do not trim excess. Repeat for the right side.
7. Now cut your ribbon into 4 equal pieces. Using two pieces, catch the D-ring and pull the ends together. Place the ribbon at the bottom of the flap on the same side as the strap. Safety Pin it in place. Do the other side the same way. Pin.
* This is a good time to fit the harness on your dog. Make sure the rings line up. Make sure it is snug, but not tight. Wrap the left side flap over the right and line up the rings. The shoulder straps should just meet in the middle. Adjust if necessary and stitch them down just as before in the binding ditch. Refer to the pattern for a reference mark.
8. Cut four pieces of ¾” hook and loop tape about 3” long. Two hook and two loop. Clip the corners off of each one if desired as in photo. Pin the loopy side to the inside of the left band encasing the raw ends of the strap and the ribbon. Stitch the two close together, making sure to go all the way around. Repeat on the right side.
9. Now your Kimono Harness is complete!
Slip your dogs paws through the straps, wrap the bands over his/her back and secure. Clip in your leash and you are off. I promise your dog will love it.
39 Responses to “Kimono Dog Harness Pattern + Tutorial”